OSHA reminder and resources for the upcoming work-related injury recordkeeping deadlines in 2026. Learn more here.

A simple fix for a major coverage gap.
As of July 1, 2025, California will adopt a new standard for fall protection in residential construction, lowering the trigger height to 6 feet across the board. This update brings California’s rules in line with federal OSHA standards, and it’s expected to affect a wide range of trades — particularly roofing and framing, but also siding, HVAC, solar, and finish work.
While this change is aimed at reducing serious injuries and fatalities from falls, it also means that many contractors will need to adjust safety procedures, retrain employees, and invest in new equipment to remain compliant.
This article outlines what’s changing, who it impacts, and how you can begin preparing now to make the transition as smooth as possible.
The Old Rule:
California’s existing standard required fall protection starting at 7.5 feet for most activities, and 15 feet for some tasks like roofing. Exceptions and workarounds were common in the residential space, particularly for short-duration or “low-risk” work.
The New Rule:
As of July 2025, fall protection will be required at 6 feet or more — no exemptions based on trade or task type. Additionally, under the new rule, vertical distance is measured from the employee’s walking/working surface to the ground or level below with the parapet height no longer being included in the roof height measurement. This change removes ambiguity and brings all residential work under the same standard.
The updated rule will apply to nearly all residential construction work involving heights of six feet or more. Trades likely to be affected include:
Notably, any roof slope steeper than 7:12 will now require fall protection at any height, not just above 6 feet. This is a significant update for contractors performing work on steep-slope roofing systems.
On multi-employer jobsites, General Contractors share responsibility for ensuring that all workers, including subcontractors, are protected from fall hazards. For more on this, visit Cal/OSHA’s guidance on multi-employer worksites.
In short: if your crews are working six feet off the ground or higher on a residential site, fall protection will soon be mandatory.
Roofing continues to be one of the most hazardous trades in construction. Recent data shows that:
Cal/OSHA’s decision is part of a broader push to reduce these numbers by aligning state rules with proven federal standards.

This change will likely require updates to your jobsite practices, crew training, and equipment. Key areas of impact include:
1.Fall Protection Systems
You’ll need to evaluate which fall protection systems make the most sense for your work. These may include:
Choosing the right system depends on the nature of your work, crew size, and access to equipment.
2.Training Requirements
With new equipment and procedures comes the need for updated training. Workers will need to be trained not just in how to use the equipment, but how to inspect it, identify fall hazards, and follow updated safety plans. Workers need to understand the fall protection procedures specific to the jobsite.
3.Worksite Assessments
Jobsite conditions change daily. Regular assessments will be needed to identify new fall risks and determine the right protective measures for each phase of work.
4.Written Fall Protection Plans
The new regulation will require employers to maintain written fall protection plans, tailored to each jobsite and updated as work progresses. If you already have a plan in place, now’s the time to review and revise it with the new trigger height in mind.
While the new rule won’t be enforced until mid-2025, contractors who begin planning now will be better positioned to adjust without disruption. This may include:
Adapting to a new regulation is never just about checking a box — it’s about making sure your crews can do the job safely, efficiently, and consistently. And while this change will require upfront effort, it’s part of a longer-term evolution in how fall protection is approached across the industry.
New tools and technologies are already reshaping what jobsite safety looks like:
Meanwhile, more architects and builders are incorporating safety infrastructure into the design phase — improving not only how buildings are built, but how people work on them.
Whether or not your team is using these tools today, it’s clear that fall safety is no longer just about reactive protection — it’s about proactive prevention.
The new 6-foot fall protection rule marks a meaningful shift in how residential construction sites are regulated — and how employers will need to approach safety moving forward. While it’s normal to feel some friction with operational changes like this, planning ahead can make the transition manageable.
Taking steps now to evaluate your needs, prepare your crews, and document your procedures will put you in a stronger position come July 2025 — and will help lay the foundation for smarter, safer jobsites long after this rule takes effect.
More guidance from Cal/OSHA is expected as the deadline approaches. Your Team here at M&G will continue to provide resources and materials as they become available, but you can also reach out to your Advisor for more support or information.
—-
Sources
Roofing Contractor. (2023, May 4). Roofing Has Second-Highest Workplace Fatality Rate in the US. https://www.roofingcontractor.com/articles/99010-roofing-has-second-highest-workplace-fatality-rate-in-the-us
Roofing Webmasters. (n.d.). Roofing Accidents – Dangers of Roofing & Workplace Hazards. https://www.roofingwebmasters.com/roofing-accidents/
Cal/OSHA. (2025, April 3). Fall Prevention: Changing Regulations and Keeping Workers Safe [Presentation]. Safe At Work California. https://www.safeatworkca.com/contentassets/2011707938af4ffc9e6b2cacbd7c80eb/fall-prevention_changing-regulations-and-keeping-workers-safe_4.3.25.pdf